#acl All:read <> The following guide applies to TCP/IP Services version 5.4 (HP TCP/IP Services for OpenVMS Alpha Version V5.4). == How can I enable IPv6 on OpenVMS? == To configure the node as an IPv6 host first login as system user, then call {{{TCPIP$IP6_SETUP.COM}}}. Answering with the default settings should be ok. If there's an IPv6 capable router in your network which advertises itself, then the host address will be configured automatically too. After that if the node has got both IPv4 and IPv6 addresses, the IPv6 stack will be used. {{{ $ @SYS$MANAGER:TCPIP$IP6_SETUP }}} {{{ IPv6 Network Configuration Procedure This procedure helps you define the parameters required to enable IPv6. This procedure will gather IPv4 information from your system then prompt you for IPv6 related information. You may enter a question mark (?) at any question for further explanation. This system can be configured as a IPv6 Host or an IPv6 Router. As an IPv6 Host, a system can autoconfigure its IPv6 address(es). If there is an IPv6 router on the same link as this host then it is capable of autoconfiguring an IPv6 global address on its interfaces based on the information carried in Router Advertisements sent by the router. As an IPv6 Router, a system is responsible for advertising one or more address prefixes to other IPv6 hosts on the link from which they can autoconfigure globally routable addresses, and for forwarding packets destined for remote address prefixes. If you answer "YES" to this question, you will be prompted for address prefixes on each interface. Configure this system as an IPv6 router? [NO]: No, only a host. This system can be configured as a 6to4 isolated host with no connection to an IPv6 network. If this system is a host within a IPv6 or a 6to4 site, do not create a 6to4 interface. An IPv6 address or a 6to4 address will be automatically configured on this system using the standard IPv6 mechanisms. A 6to4 interface is needed only if this system is an isolated host with no connection to the IPv6 network. Configure a 6to4 interface? [NO]: Do you want to enable IPv6 on this interface? Enable IPv6 on interface WE0? [YES]: Yes, that's what we want. Automatic tunnels allow multiple IPv6 nodes connected to an IPv4 network to communicate with IPv6 messages without explicitly creating configured tunnels between each pair of nodes. Automatic tunnel endpoints are identified by IPv4-Compatible IPv6 addresses of the form ::ddd.ddd.ddd.ddd. The last four bytes of an IPv4- Compatible address define the IPv4 address of the tunnel endpoint. HP recommends you avoid using automatic tunnels due to potential IPv4-Compatible address routing problems. Answer "YES" to enable automatic tunnels on this system. Configure an IPv6 over IPv4 automatic tunnel interface? [NO]: An IPv6 over IPv4 configured tunnel allows an IPv6 node to communicate with another IPv6 node across an IPv4 network. IPv6 messages are encapsulated inside IPv4 messages for transmission. Each configured tunnel has just one source and one destination in the IPv4 network. Answer "YES" to create a configured tunnel on this system. Create a configured tunnel? [NO]: Create IPv6 Host configuration file? Please enter YES or NO [YES]: Yes, save it. A new IPv6 configuration file, SYS$SYSTEM:TCPIP$INET6_CONFIG.DAT, has been created. The previous configuration file (if any) has been renamed to SYS$SYSTEM:TCPIP$INET6_CONFIG.DAT_OLD. This new IPv6 configuration will become active the next time TCP/IP Services for OpenVMS is started. }}} Then restart the TCP/IP services, and IPv6 should be working. == How to check if IPv6 enabled on OpenVMS? == Check the configuration with listing the interface parameters. {{{ $ TCPIP TCPIP> ifconfig we0 WE0: flags=c43 *inet 193.6.5.197 netmask ffffff00 broadcast 193.6.5.255 ipmtu 1500 inet6 fe80::a00:2bff:fee7:eb88 inet6 2001:738:6001:500:a00:2bff:fee7:eb88 TCPIP> ifconfig lo0 LO0: flags=100c89 inet 127.0.0.1 netmask ff000000 ipmtu 4096 inet6 ::1 }}} Can be easily tested with a simple ping: {{{ TCPIP> ping suti.iit.uni-miskolc.hu PING suti.iit.uni-miskolc.hu (2001:738:6001:500::ffff): 56 data bytes 64 bytes from 2001:738:6001:500::ffff: icmp6_seq=0 hlim=64 time=2 ms 64 bytes from 2001:738:6001:500::ffff: icmp6_seq=1 hlim=64 time=1 ms 64 bytes from 2001:738:6001:500::ffff: icmp6_seq=2 hlim=64 time=1 ms 64 bytes from 2001:738:6001:500::ffff: icmp6_seq=3 hlim=64 time=1 ms ----suti.iit.uni-miskolc.hu PING Statistics---- 4 packets transmitted, 4 packets received, 0% packet loss round-trip (ms) min/avg/max = 1/1/2 ms TCPIP> ping skye.ki.iif.hu PING skye.ki.iif.hu (2001:738:0:402::2): 56 data bytes 64 bytes from 2001:738:0:402::2: icmp6_seq=0 hlim=60 time=8 ms 64 bytes from 2001:738:0:402::2: icmp6_seq=1 hlim=60 time=5 ms 64 bytes from 2001:738:0:402::2: icmp6_seq=2 hlim=60 time=5 ms 64 bytes from 2001:738:0:402::2: icmp6_seq=3 hlim=60 time=5 ms ----skye.ki.iif.hu PING Statistics---- 4 packets transmitted, 4 packets received, 0% packet loss round-trip (ms) min/avg/max = 5/6/8 ms }}} Or with traceroute: {{{ TCPIP> trace skye.ki.iif.hu traceroute to skye.ki.iif.hu (2001:738:0:402::2): 1-30 hops, 64 byte packets 1 suti6.iit.uni-miskolc.hu (2001:738:6001:500::ffff) 1.953 ms 1.953 ms 1.95 3 ms 2 2001:738:6000:200::1 (2001:738:6000:200::1) 1.953 ms 1.953 ms 0.976 ms 3 lo0.c6509.vh.hbone.hu (2001:738:0:4::1) 5.859 ms 4.882 ms 5.859 ms 4 2001:738:0:406::1 (2001:738:0:406::1) 5.859 ms 4.883 ms 5.859 ms 5 skye.ki.iif.hu (2001:738:0:402::2) 7.812 ms 6.836 ms 5.859 ms }}} On top of that, the neighbour discovery daemon should appear among the processes. {{{ $ show system ... 00000216 TCPIP$ND6HOST LEF 9 8923101 0 00:00:19.14 372 230 ... }}}